7900-6061/A Coleman 2 speed A/C blower assembly 1 to 3 tons AC
7900-6061/A Coleman 2 speed A/C blower assembly
Backorder from the factory
NOTE: when receiving a new blower unit the blower wheel will need to be adjusted and centered on the motor shaft and remove cardboard packing. They ship from the factory with the blower wheel pushed to the one side of the blower unit to keep the blower wheel in round position
to adjust loosen square head locking bolt and slide the blower wheel to the center of the motor shaft and make sure you have equal clearance on both sides of the blower assembly.
2 SP AC BLOWER 2 speed A/C blower assembly for gas furnaces. Used with air conditioners up to 3.0 tons.
If you are looking for a replacement blower assembly for the Coleman 7600 series, COAS, COAT furnaces, this is a drop-in replacement. It will replace the old blower assembly with the included adapter plates. For units with air conditioners, you may have to add a transformer to the outside unit as the condenser units had the transformer in them during that era.
| Component | Coleman P/N | Description |
|---|---|---|
| Blower Motor | 1468-220P | 2-speed, 1/3 HP, 1075 RPM |
| Blower Wheel | 026-24069-700 | 10″ × 7″ double-inlet, precision-balanced |
| Motor Clamp | 7670-5391 | Rubber isolation mounts |
| Run Capacitor | 024-20063-700 | 7.5 µF, 440 VAC |
| Rubber Mounts | 2702-4091 | Vibration-damping mounts |
| Legacy Assembly | 7900-6031 / S1-7900-6031/A | Original replacement part numbers |
Technician Notes
Installation and adjustment guidelines for the 7900-6061/A assembly:
-
Remove all cardboard shipping blocks before powering up.
-
Loosen the square-head locking bolt and slide the blower wheel to center it on the motor shaft; confirm equal clearance on both sides.
-
Verify 120 VAC at motor terminals and correct 9-pin Molex connections before start-up.
-
Ensure the 7.5 µF run capacitor is properly seated and rated at 440 VAC.
-
Adapter plates are provided for Coleman 7600-series, COAS, and COAT furnaces; confirm hole-pattern alignment.
Compatibility
Compatible applications and common OEM models for the 7900-6061/A blower assembly:
- Used to replace existing blower when adding air conditioning to an existing heat only system or 3-1/2 tons or more A/C to a new system
- Used when adding 3 tons or less A/C to Evcon gas furnaces that are not A/C ready or MGHA or MMHA series Nordyne gas funaces, or when adding 3 tons of A/C to DGAT/C or DGAT/D series Evcon furnaces less than 90,000 BtuH input
| Application | Models / Series |
|---|---|
| Coleman Gas Furnaces | 7600 series, COAS, COAT |
| Split-System Air Conditioners | Up to 3.0 ton condenser units |
| Legacy Replacement | Replaces 7900-6031 / S1-7900-6031/A |
| Aftermarket Retrofits | 10″ × 7″ blower housings in range hoods or light commercial units |
The Coleman 7900-6061/A blower assembly is designed for 1 to 3 ton A/C systems, and typically produces approximately 800 to 1,200 CFM depending on static pressure and speed setting.
🔧 Key Specs
-
Motor: 2-speed, 1/3 HP, 1075 RPM (P/N 1468-220P)
-
Blower Wheel: 10" × 7" double-inlet (P/N 026-24069-700)
-
CFM Range:
-
Low Speed: ~800–900 CFM
-
High Speed: ~1,000–1,200 CFM
-
-
Voltage: 120V
Replaces the 7900-6031 S1-7900-6031/A.